Product Name

10/100/1000Mbps Managed Industrial Fiber Switch with CAN Bus and RS485

Model No.

IM-FS880GW-2C4D

Port

8 x 1000Mpbs SFP port

SM:1310nm/1550nm,20Km ;1490nm/1550nm, 40~120Km; MM:1310nm, 2Km;

8x10/100/1000M UTP RJ45(Support MDI/MDIX auto-sensing)

2 x CAN Bus (Standard frame 11-bit ID, extended frame 29-bit ID,

Support J1939, CANopen, DeviceNet and other protocols (firmware configuration required)

4 x RS485 (support TCP/UDP protocol)

1 x Console port (RJ45, Baud rate: 115200)

Standard

IEEE 802.3, IEEE802.3U, IEEE802.3ab, IEEE802.3z, IEEE802.1d STP, IEEE802.1w RSTP, IEEE802.1s MSTP, ITU-T G.8023 EPR/Y.1344, IEEE802.1Q, IEEE802.1X, IEEE802.3ad, IEEE802.3x, IEEE802.1ad, IEEE802.1p, IEEE802.1ab, IEEE802.3az

VLAND ID

4096

Jumbo Frame

9.6KB

MAC Address Table Size

8K

Switching Features

Transmission mode:storage and forward

System bandwidth:58Gbps (non-traffic jam)

DRAM size: 128M Flash size: 16M Packet buffer size: 4Mb

Protocol

IEEE 802.3(10Base-T)

IEEE 802.3u(100Base-TX)

IEEE 802.3ab(1000Base-TX)

IEEE 802.3z (1000Base-X )

IEEE 802.1D (STP)

IEEE 802.1w (RSTP)

IEEE 802.1s (MSTP)

ITU-T G.8032 ERPS Ring

IEEE 802.1Q( VLAN)

IEEE 802.3x (Flow control)

IEEE 802.3ad (LACP)

IEEE 802.1p (QoS)

IEEE 802.1ab(LLDP)

IEEE 802.1az(EEE)

RFC 768 UDP

RFC 793 TFTP

RFC 791 IP

RFC 792 ICMP

RFC 2068 HTTP

RFC 1112 IGMP v1

RFC 2236 IGMP v2

RFC 3376 IGMP v3

L2+ Managed

Supports IEEE802.1q VLAN, port VLAN, based Mac VLAN, IP subnet VLAN, protocol VLAN, VLAN conversion MVR.

Supports IEEE802.3az EEE (Energy Efficient Ethernet) Management, optimizes power consumption.

Supports STP, RSTP, MSTP, ITU-T G.8032 Ethernet Protection Ring (EPR).

Supports QoS, transmission classification QoS, CoS, bandwidth control (input/output direction), storm suppression, differential services.

Supports dynamic IEEE 802.3ad LACP link aggregation, static link aggregation.

Supports IGMP/MLD detection V1/V2/V3, IGMP filtering/adjustment, IGMP query.

Supports IGMP proxy report, MLD detection.

Security: based on port and Mac IEEE802.1X, RADIUS, ACL.

Support IEEE802.3az EEE (Energy Efficient Ethernet) TACACS+, HTTP/HTTPS, SSL/SSH v2.

Support Cisco® like CLI, Web network management, SNMP v1/v2c/v3, Telnet.

Support software upgrade via TFTP and HTTP, firmware redundancy to prevent upgrade failure.

Support RMON, MIB II, mirroring, event log, DNS, NTP/SNTP, IEEE802.1ab LLDP.

Support IPV6, ICMP v6NTP/SNTP, TFTP, QOS, ACL.

Support SerialCRT,CLI,Telnet,SNMP,HTTP,SSH/SSL

Power Supply

DC12-52V, redundant dual power input and support reverse polarity

No-load power: 3.6W

Full-load power: 11.2W

CAN Bus

Standards: ISO 11898-2 (high-speed CAN)

Communication rate: 10Kbps~1Mbps (configurable)

Maximum number of nodes: 110 (default terminal resistance matching)

Terminal resistance: 120Ω (optional terminal resistance built-in for each CAN)

Isolation protection: Supports 2500V DC isolation (optional)

Communication protocol: Supports CAN 2.0A/B, CAN FD

Bus voltage range: -3V ~ +32V (anti-surge protection)

RS485

Standards: TIA/EIA-485-A

Working mode: Full-duplex or half-duplex (configurable)

Communication rate: 115200bps (configurable)

Maximum number of nodes: 32 (default) or expandable to 256 (repeater required)

Isolation protection: Supports 1500V DC isolation (optional)

Bus voltage range: -7V ~ +12V (surge protection)

RS485/CAN Stability

Continuous 72-hour full-load communication test under extreme temperature, communication bit error rate ≤1e-9

LEDs

Power, network, fiber, system

Environment

Working Temp:-40°～ 75°C ; Storage Temp:-40°～ 85°C;Working humidity:10%～90%, non-condensing; Storage humidity:10%～95%, non-condensing

Industry Standards

Ethernet/SFP interface:

IEC61000-4-2 (ESD, electrostatic discharge immunity)

Air discharge: ±15KV

Contact discharge: ±8KV

IEC61000-4-4 (EFT, electrical fast transient pulse interference)

Signal: ±6KV

IEC61000-4-5 (Surge, surge lightning interference)

Signal: differential mode ± 2KV

Common mode ± 6KV

RS485/CAN interface:

IEC 61000-4-2 (ESD, electrostatic discharge immunity)

Contact discharge: ±8KV

IEC 61000-4-5 (Surge, surge and lightning interference)

Signal: differential mode ± 2KV

Safety

CE-EMC:

EN 55032:2015+AC:2016+A1:2020+A11:2020

EN 55035:2017+A11:2020/EN IEC 61000-3-2:2019/A1:2021

EN 61000-3-3:2013/A2:2021/AC:2022

CE-LVD:

EN IEC 62368-1:2020+A11:2020

FCC:

47 CFR FCC Part 15 Subpart B (Class B) ANSI C63.4:2014

Mechanical information

Shell:Corrugated metal shell; Safety class:IP40;

Dimension:158 x 114.8 x 60mm;

Mounting method:Din-rail mounting

Industrial Optical Module

OSPL1G05D

1000BASE-SX

OSPL1G06D

1000BASE-SX(1310nm)

OSPL1G20D

1000BASE-LX

OSPL1G40D

1000BASE-EX

OSBL1G20D-35

1000BASE-BX-U(TX 1310 RX1550)

OSBL1G20D-53

1000BASE-BX-D(TX 1550 RX1310)

Industrial DIN Power Supply

IM-DAC220/DC12V1.67A

AC220V to DC12V1.67A, -30℃～70℃

IM-DAC220/DC24V1A

AC220V to DC24V1A, -30℃～70℃