10 Port Layer 2 Web Managed Industrial Gigabit Switch
Introduction
- IM-FS280GW series is the 10/100/1000 Mbps industrial fiber switch
operating temperature -40℃ to +75℃.
- Support wide voltage dual power input, support web management.
- Meet IP40 protection degree and EMC industrial grade requirements
- DIN rail installation
- Pass through dangerous environmental certification and comply with
FCC and CE standards
- The reliable industrial grade design could ensure continuous and
stable operation of the automation system.
Key Features
- 6KV Ethernet surge protection, adapt to a harsh outdoor environment
- Support Auto MDI/MDIX
- Flow control mode: full duplex with IEEE 802.3x standard,
half-duplex with Back pressure standard
- IEEE 802.3 10Base-T and IEEE 802.3u 100Base-TX compliant
- A store-and-forward switching mechanism
- Support cable diagnosis and can locate the fault point
- Support IEEE802.3az EEE (Energy Efficient Ethernet) Management,
optimize power consumption
- Support STP, RSTP, MSTP, ITU-T G.8032 Ethernet Protection Ring(EPR)
- Support Qos, transport classification Qos, Cos, bandwidth control
(input/output direction), storm suppression , differentiated
services
- Support IEEE802.1q VLAN,VLAN port ,based Mac VLAN,IP subnet
VLAN,Protocol VLAN,VLAN convert, MVR
- Support dynamic IEEE802.3ad LACP link aggregation, static link
aggregation
- Support IGMP/MLD snooping V1/V2/V3, IGMP filtrating/ modulating,
IGMP searching
- Support IGMP agent report, MLD snooping
- Safety: based on port and Mac IEEE802.1X, RADIUS, ACL,
TACACS+,HTTP/HTTPS, SSL/SSH v2
- Support Cisco® like CLI, Web management, SNMP v1/v2c/v3, Telnet
- Support software upgrade via TFTP and HTTP, firmware redundancy
prevents upgrade failing
- Support DHCP client/Relay/Snooping/Snooping option 82/Relay option
82
- Support RMON, MIB II, mirror image, event log, DNS, NTP/SNTP,
IEEE802.1ab LLDP
- Support IPV6 Telnet server /ICMP v6, SNMP, HTTP, SSH/SSL,
NTP/SNTP,TFTP, QoS, ACL
Specification
| Product name | 10/100/1000Mbps Managed Industrial Fiber Switch (2F+8TP) |
| Model No. | IM-FS280GW |
Port | 2x 100M/1G/2.5G SFP ports SM: 1310nm/1550nm, 20Km; 1490nm/1550nm, 40~120Km MM: 1310nm, 2Km; 850nm, 500m 8x10/100/1000M UTP RJ45(Support MDI/MDIX auto-sensing) |
Standard | IEEE 802.3, IEEE802.3U, IEEE802.3ab, IEEE802.3z, IEEE802.1d STP IEEE802.1w RSTP, IEEE802.1s MSTP, ITU-T G.8023 EPR/Y.1344 IEEE802.1Q, IEEE802.1X, IEEE802.3ad, IEEE802.3x, IEEE802.3af IEEE802.3at, IEEE802.1ad, IEEE802.1p, IEEE802.1ab, IEEE802.3az |
VLAND ID | 4096 |
Jumbo Frame | 9.6K |
| MAC Address Table Size | 8K |
Switching features | Transmission mode: storage and forward System bandwidth: 26Gbps (non-traffic jam) DRAM size: 128M Flash size: 16M
Packet buffer size: 4Mb |
Network media | 10BASE-T: CAT3, CAT4, CAT5 un-shielded twisted pair(≤100m) 100/1000BASE-TX: CAT5 or above shielded twisted pair(≤100m) SFP port,transmission distance: 20Km,40Km,60Km,80Km,100Km |
LEDs | Power, network, fiber |
Power supply | Input voltage:DC 12-52V No-load power:5W Reverse connection: support |
Environment | Working temperature: -40～75°C Storage temperature: -40～85°C Working humidity: 10%～90%, non-condensing Storage humidity: 10%～95%, non-condensing |
| Mechanical information | Shell:Corrugated metal shell Safety class:IP40 Dimension:158 x 114.8 x 60mm Mounting method:Din-rail mounting |
Application
.
FAQ
How can I install the device?
A: Each model in this series supports DIN35/Wall mounting.
It requires necessary accessories in installation like screws,
mounting kit etc., some of them are included in the packing box,
some are not.
Does your switch support 155Mb/s tranceivers?
A: Yes, the optical speed is 100M/1000M/2500M. Please just
configure 100M speed in the management interface, megabit modules
are working.
Can you let me know how the indicators work?
A: This is our Vitesse based managed switch series and all models
share the same indicator definition as below.
PWR: Power
FX: Fiber port(1/2/3/4)
Orange: Link/ACT
Green: 1000M Network Speed(off when it is 100Mb/s)
Do you do SKD/CKD?
A: Yes, we have dealt with this many times.
As a factory, we have enough energy and resources to handle this.
Can I add my logo/model in the management?
A: Yes, it is easy and free of cost, please just send your model
name and logo in PS/AI format. We will do the rest and send a photo
for your confirmation.
Do your switches support any ring protocols?
A: Yes, our switches support STP/RSTP/MSTP and ERPS for ring
configuration.
